connectCAD at Infocomm17

Meet us at Infocomm - Vectorworks booth #4226

Find out all you'd like to know about about connectCAD at Infocomm 2017, June 14-16 at Orlando Florida, Orange County Convention Center - at the Vectorworks booth #4226. Special manufactures training session on Thursday, June 15 from 10:30am – 12pm “Simplify Your Systems Integration Design and Documentation Workflow“ This presentation covers the workflow between Vectorworks and connectCAD. It is hosted by Jim Woodward, Vectorworks Industry Specialist and Chuck Walthall, connectCAD US Support Consultant, Audiovisual Consultant & Designer.
You may register here

AV designer Justin Linville from Provision Audio Video Solutions describes how connectCAD facilitated the process of audiovisual integration in a new church facility.

May 2017

House of Worship AV design with connectCAD
Photo credit: Provision AudioVideo Solutions

“From the start of this project, we talked about digital audio networks and integrating all the spaces in a way that would make it really easy to configure whatever audio paths were needed going from one location to another. We used a variety of Dante-based interfaces to get audio in and out at various locations, and that really added a big big level of versatility to the whole project. There was a lot of the design that looked very very similar to network topology, so we had to plan certain switches, and we had to plan all the cable paths and the interconnections really meticulously, so there was a lot from the beginning that really added to the complexity of the design.”

“Because of the way this project evolved over time, we sort of evolved the system design with the industry offerings. We had a lot of options in terms of flexibility, and because of the various in and out points of the a/v network, we had to develop a very concise plan before heading into installation. This is where the connectCAD tool came in and really made a difference. For example, every time you change one component in a typical CAD system, you have to go in there and redraw all the connections, and you have to reconfigure all your routing paths etc. But, on the connectCAD system, with all of the tools that are available (and ever-growing), that becomes a real breeze. So, I can take a 40 mic/line input module and use the ‘multi-connect’ tool to get all 40 of my connections in about 2 seconds; whereas with the conventional CAD approach that would take an hour to redraw all 40 of these connections and get them properly labeled and assigned.”
Read the full story in our blog

Meet us at NAB show 2017 - booth #SL6324

April 2017

If you are visiting the NAB show 2017, 22-27 April in Las Vegas, you are invited to stop by the MAXON -Vectorworks/connectCAD booth #SL6324. Explore streamlined Audio Visual design workflow from room layouts to schematic designs.

From room layouts to schematic designs, explore streamlined Audio Visual design workflow

If you are visiting the NAB show 2017, 22-27 April in Las Vegas, you are invited to stop by the MAXON - Vectorworks booth #SL6324.

Meet up with the Spotlight staff, who will demonstrate how to work smarter and more efficiently and best practices for audio visual system design & documentation, from layouts, to 2D/ 3D presentations, schematics and even bill of materials.

If you are not currently using Spotlight + connectCAD and for more personalized solutions, you can also book a demo presentation during the dates of the show.  

See you at the NAB!

connectCAD 2017 version 2: Save hours of data entry with connectCAD’s online Device Sharing

March 2017

connectCAD 2017 version 2 is released, taking audio visual design to the next level.

Conrad Preen, AV designer & connectCAD’s developer, comments: “Nobody likes filling in forms, particularly a humungous one like Device Builder with all its mind-boggling details. As designers, we can’t get away from spec sheets & data entry, but at least we can share the work between us.

DevBuilderv2

Upgraded Device Builder

In connectCAD 2017, as you create devices in Device Builder, all specs get uploaded to connectCAD’s shared library and are then available to other designers who’ll want to use the same device at any later time. Already there are more than 200 regularly-used devices in the database and more are being added every day by connectCAD’ers from all over the planet.

This way, when creating a new device for your project, you can just browse the community database from within the Device Builder tool, write a name for your device, select the make, select the model and immediately all the details are loaded, so the device is ready in your schematic in just 20 seconds!
If your device cannot be found, or if some specs are missing, you can fill out all details, click Upload and contribute to the Shared Device Library. So, if all designers contribute to this library, soon data entry will be a thing of the past.

To make things even easier, connectCAD offers an automatically updated list of all device definitions uploaded to the shared library. Instead of searching in each manufacturer’s website, you can now browse through a multitude of devices all gathered together in our support site Device List .

Device Sharing is a community service hosted on connectCAD.com, a revolutionary way to make system design process faster than ever before. As you work, life keeps on getting easier.

New Connect Tool in connectCAD for Vectorworks

New Connect Tool

In connectCAD 2017 version 2 we’ve introduced our new Connect tool which follows all standard Vectorworks user-interface conventions – a faster, smoother, more intuitive alternative to our current tool, a small taste of connectCAD 2018.

cookie directive
Popup-Login

gsdfgsdgsd

sgsdgdsfg

Popup-Ask

FAQ first

We'd like to hear from you!

If you need any information about connectCAD and our company or you have a question, just fill in the form below and we'll be in touch.

Popup-Login

gsdfgsdgsd

sgsdgdsfg

Popup-Ask

FAQ first

We'd like to hear from you!

If you need any information about connectCAD and our company or you have a question, just fill in the form below and we'll be in touch.